SFP-10G-CABLE-X
SFP+ Direct Attach Passive Copper Cables , 1m、3m、5m Reach
Features
-
Support for multi-gigabit data rates up to 10.5Gbps
-
Data rates backward compatible to 1Gbps
-
Support for 1x, 2x, 4x and 8x Fibre Channel data rates
-
Hot-pluggable SFP 20PIN footprint
-
I/O Connector designed for high speed differential signal applications
-
Improved Pluggable FormFactor(IPF) compliant for enhanced EMI/EMC performance
-
Compatible to SFP+ MSA
-
Temperature Range: 0~ 70 °C
-
RoHS Compatible
Applications
-
High capacity I/O in Storage Area Networks, Network Attached Storage, and Storage Servers
-
Switched fabric I/O such as ultra high bandwidth switches and routers
-
Data center cabling infrastructure
-
High density connections between networking equipment
Product Description
The SFP+ passive cable assemblies are high performance, cost effective I/O solutions for 10G Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Recommended Operating Conditions
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Storage Ambient Temperature |
|
-40 |
|
+85 |
°C |
|
Operating Case Temperature |
Tc |
0 |
|
+70 |
°C |
Systems
|
Performance |
Media |
10.5 Gpbs line speed, full duplex
Bit error rate: better than 10E-12 |
Hot-pluggable, industry-standard Small Form-Factor
Pluggable(SFP+) copper cable, available as 1m,3m or 5m. |
Pin Descriptions
|
Pin |
Logic |
Symbol |
Name/Description |
Notes |
|
1 |
|
VeeT
|
Transmitter Ground
|
|
|
2 |
LV-TTL-O |
TX_Fault |
N/A |
1 |
|
3 |
LV-TTL-I |
TX_DIS |
Transmitter Disable |
2 |
|
4 |
LV-TTL-I/O |
SDA |
Tow Wire Serial Data |
|
|
5 |
LV-TTL-I |
SCL |
Tow Wire Serial Clock |
|
|
6 |
|
MOD_DEF0 |
Module present, connect to VeeT |
|
|
7 |
LV-TTL-I |
RS0 |
N/A |
1 |
|
8 |
LV-TTL-O |
LOS |
LOS of Signal |
2 |
|
9 |
LV-TTL-I |
RS1 |
N/A |
1 |
|
10 |
|
VeeR |
Reciever Ground |
|
|
11 |
|
VeeR |
Reciever Ground |
|
|
12 |
CML-O |
RD- |
Reciever Data Inverted |
|
|
13 |
CML-O |
RD+ |
Reciever Data Non-Inverted |
|
|
14 |
|
VeeR |
Reciever Ground |
|
|
15 |
|
VccR |
Reciever Supply 3.3V |
|
|
16 |
|
VccT |
Transmitter Supply 3.3V |
|
|
17 |
|
VeeT |
Transmitter Ground |
|
|
18 |
CML-I |
TD+ |
Transmitter Data Non-Inverted |
|
|
19 |
CML_I |
TD- |
Transmitter Data Inverted |
|
|
20 |
|
VeeT |
Transmitter Ground |
|
1. Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor
2. Passive cable assemblies do not support LOS and TX_DIS
Ordering information
|
Part Number |
Product Description |
|
SFP-10G-CABLE-1 |
SFP+ Direct Attach Passive Cable (10GSFP+Cu), 1m, AWG:30, 0ºC ~ +70ºC |
|
SFP-10G-CABLE-3 |
SFP+ Direct Attach Passive Cable (10GSFP+Cu), 3m, AWG:26,0ºC ~ +70ºC |
|
SFP-10G-CABLE-5 |
SFP+ Direct Attach Passive Cable (10GSFP+Cu), 5m, AWG:24,0ºC ~ +70ºC |
Note: 传输距离同时取决于客户设备对信号的驱动能力和预加重功能，为此You can be customized diameter and distance.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be
specifically confirmed in writing by F-TONE before they become applicable to any particular order or
contract. In accordance with the F-TONE policy of continuous improvement specifications may change
without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-TONE or others. Further details are available from any F-TONE sales representative.
